Call us 24/7+86 15396212224

ABB’s new Carlon fan-rated ceiling boxes raise the bar on home safety

.Engineered to meet the latest industry standards, the new Carlon® Blue™ fan-rated ceiling boxes from ABB Installation Products help protect and power residential and light commercial installations

.Supports growing demand for energy-efficient ceiling fans in home improvements and new construction

.Sustainably produced in Tennessee, extensively tested and backed by an Environmental Product Declaration, Carlon® Blue™ non-metallic electrical boxes are trusted by contractors and homeowners

More than 70% of American households have at least one ceiling fan, and nearly a quarter use four or more. Increasing demand for energy-efficient ceiling fans with integrated technology and smart features is spurring the need for properly rated support. The new Carlon® Blue™ fan-rated ceiling boxes from ABB Installation Products are engineered for easy installation and to safely support a fan’s weight, vibration and movement, in compliance with the latest National Electric Code (NEC) outlet box requirements for ceiling-suspended fans.

Improperly installed ceiling fans lead to an estimated 20.000 injuries annually in the United States. To help improve home safety, the 2020 NEC requires ceiling outlet boxes in homes, including rooms where ceiling fans may be installed now or later, to either be listed for the sole support of ceiling-suspended fans or provide access to structural framing capable of supporting a ceiling fan bracket. ABB’s Carlon Blue ceiling boxes are rated for a 50-pound light fixture and 35-pound ceiling fan, with vibration-resistant screws through reinforced metal brackets that provide greater strength than plastic alone.

“Ceiling fans are used year-round in millions of homes and are often an overlooked safety risk. www.honeywell-diver.com Our new Carlon Blue fan-rated ceiling boxes address the needs of contractors and homeowners for a safe, smart and sustainable solution,” said Jack Bellissimo, Senior Vice President, Product Management, Marketing & Strategy, ABB Installation Products. “Authentic Carlon boxes in our distinctive blue color are responsibly produced in Tennessee and meet the 2020 NEC code to perform safely and reliably.”

Commitment to safety and circularity

ABB’s Carlon Blue fan-rated ceiling boxes conform to UL 514C and meet NEC 314.27 (C) requirements for use in habitable and non-habitable rooms. Designed for new construction, the 4-inch diameter round boxes are available with an L-bracket for secure fan mounting or an adjustable bar hanger to position between ceiling joists. These boxes are available with or without a grounding screw.

Made in Portland, Tennessee, Carlon® Blue™ non-metallic boxes are produced using repurposed material from injection molding processes, diverting nearly 110 metric tons of waste from landfills each year. Covered by a third-party verified Environmental Product Declaration (EPD), consumers can make informed decisions about the energy usage, resource consumption and emissions used to manufacture Carlon products installed in their homes.

Building on its long history of pioneering in electrification, ABB Installation Products creates solutions to safely connect and protect electrical systems that power businesses, cities, homes and transportation. With more than 200.000 products under 38 premium brand names, ABB Installation Products, formerly Thomas & Betts, solutions are found wherever electricity is used around the world and in space.

ABB is a technology leader in electrification and automation, enabling a more sustainable and resource-efficient future. The company’s solutions connect engineering know-how and software to optimize how things are manufactured, moved, powered and operated. Building on over 140 years of excellence, ABB’s more than 105.000 employees are committed to driving innovations that accelerate industrial transformation.

ABB Harnessflex Interconnect™ System

Harnessflex Interconnect™ System

A Multi-Sleeve Adaptor for the fastening of Harnessflex fittings and connector interfaces to braiding, sleeving, heat-shrink, self-close wrap and other common forms of cable protection.

Harnesflex Interconnect™ System (Multi-Sleeve Adaptor), allows free rotation of braid and sleeving relative to backshell or fitting, reducing strain, intrusion and impact damage – all of which can lead to electrical faults and vehicle failure.

The Multi-Sleeve Adaptor (MSA/MSAR) is compatible with Harnessflex hinged fittings and connector interfaces.

Features & benefits:

Easily secured with Ty-Rap® cable ties or Harnessflex Multi-Function clips

Hold cable bundles inside conduit

Smooth cable entry and bore

Easy assembly

External hinged connector interfaces – tough and durable protection for OEM connectors against high pressure wash-down, excessive cable strain and abrasion

Connect seamlessly with Multi-Sleeve Adaptor

Internal conduit backstop provide insertion guide ensuring system integrity and high pull off strength

Hold cable bundles inside slit conduit and reduce risk of cables protruding out

Reduce vibration risk by minimising impact of cable on conduit inner wall

ABB creates universally compatible multi-sleeve adaptor to help protect wiring in heavy-duty vehicles

OEM-agnostic Harnessflex® Interconnect system from ABB Installation Products works with common types of cable protection

Improves heavy-duty vehicle cable protection with unilaterally effective cable-to-connector stability

Addresses critical connection challenges across global heavy-duty EV market and transport sector

Imagine a heavy-duty vehicle or electric vehicle (EV) grinding to a halt – not due to a battery issue, www.honeywell-diver.com but because of a faulty electrical connection. Heavy-duty vehicles endure constant vibration, impact and strain, which can compromise vehicle safety and lead to costly downtime. ABB Installation Products addresses these challenges with the first-of-its-kind Harnessflex® Interconnect system. This is a multi-sleeve adaptor designed for universal compatibility across common types of cable protection and Harnessflex® fittings and connector interfaces, simplifying and strengthening cable-to-connector stability essential to the reliable operation of heavy-duty vehicles.

The rise of heavy-duty EVs and shifting regulatory requirements necessitates robust electrical systems capable of handling higher voltages and operating temperatures, as well as protecting vital connections from demanding conditions and harsh operating environments. To secure electrical connections in heavy-duty vehicles, harnessmakers use a variety of cable protection solutions such as braids, sleeves, wraps, jackets, heat shields and conduits. Previously, these forms of cable protection have often been used with critical wiring into connectors left exposed due to no backshell compatibility.

Harnessmakers can now seamlessly integrate the OEM-agnostic Harnessflex Interconnect system with their choice of cable protection methods, helping ensure critical connections are shielded from elements such as dirt, oil, high-pressure washdowns, corrosive chemicals and more. As a reusable system, the Harnessflex multi-sleeve adaptor is a more sustainable solution than plastic tape, shrink wrap and other items commonly used to secure cables at critical electrical junctions.

“Vehicle makers face capacity constraints as they work to meet tighter industry standards. ABB is creating solutions to help streamline installation, optimize cable protection and significantly improve the overall reliability of heavy-duty vehicles,” said Andrea Castella, EVP and General Manager, ABB Installation Products for Europe, Asia Pacific, Middle East and Africa. “ABB’s Harnessflex Interconnect system expands our electrification solutions across a broad range of high-use transportation and heavy-duty applications.”

MAN Diesel Master Control Unit 1881610-7

Product Identification:

Model/Number: 1881610-7

Manufacturer: MAN Diesel & Turbo

Functionality:

The MAN Diesel Master Control Unit 1881610-7 serves as a crucial component in the monitoring, control, and optimization of diesel engine power systems in marine applications.

Technical Specifications:

It features an expansion cable assembly that provides a flexible interconnection, allowing for the transmission of bus signals and power between two components.

The expansion cable assembly consists of a cable socket component (located on the left side of the base unit) and a cable plug component (located on the right side of the base unit).

It includes a fault reset button, located on the 9110 front panel processor module, for instantaneous action in case of faults.

The Master Control Unit is designed with fault-tolerant systems that provide continued correct operation in the event of a limited number of hardware and software failures.

Operation and Safety:

It is essential to adhere to the safety regulations and operational guidelines provided by MAN Diesel & Turbo to ensure safe and accurate operation of the Master Control Unit.

Proper maintenance and timely troubleshooting are crucial to maintaining the reliability and efficiency of the system.

Additional Information:

Contact MAN Diesel & Turbo or its authorized service centers for detailed technical specifications, user manuals, and maintenance guidelines specific to the MAN Diesel Master Control Unit 1881610-7.

This description provides a concise overview of the key features, functionality, and technical specifications of the MAN Diesel Master Control Unit 1881610-7.

I. Product Overview

Model and Manufacturer: Model 1881610-7. manufactured by MAN Diesel & Turbo.

Use: As a key part of the marine engine control system, it is used to monitor, control and optimize the power system of diesel engines.

II. Technical features

Fault indication: with binary fault indication function, it is able to quickly recognize and indicate system faults.

Expandability: Expansion cable assemblies may be fitted to provide flexible interconnection options to support the transfer of bus signals and power between components.

Fault Reset: A fault reset button may be provided on the control panel to allow immediate action in the event of a fault.

Fault Tolerant System: A fault tolerant system is designed to ensure a degree of correct operation even in the event of a hardware or software failure.

III. Operation and Maintenance

Operating instructions: Users should refer to the operating instructions and safety regulations provided by MAN Diesel & Turbo for operation to ensure safe and accurate operation of the system.

Maintenance Requirements: Regular maintenance and inspection is the key to ensure long-term stable operation of the system. This includes cleaning, tightening, and replacing worn parts.

Troubleshooting: The system may be equipped with troubleshooting tools or software to help users quickly identify and solve problems.

Translated with DeepL.com (free version)

GE General Electric 04220FL11232A RXI Controller

GE General Electric 04220FL11232A  RXI Controller, Multiple Ethernet Ports, 3.4 Amp, 24 VDC

I. Introduction

In the field of industrial automation, the performance of the controller is directly related to the operation efficiency and stability of the whole system. GE RXI controller has become a leader in the field of industrial automation with its excellent performance, rich functions and stable operation. In this paper, we will introduce in detail the characteristics and parameters of GE RXI controller and its application in industrial automation.

Overview of GE RXI controller

GE RXI controller is a high-performance, high-reliability control system introduced by GE Intelligent Platform. It utilizes cutting-edge CPU technology, market-leading industrial Ethernet network technology, and a unique user interface to provide equipment manufacturers and end-users with the most efficient and reliable control system.

Third, the GE RXI controller parameters in detail

Processor: The GE RXI controller utilizes a high-performance dual-core CPU to ensure efficient system operation.

Memory: The RXi Box IPC has 4G RAM memory to support high-performance designs.

Storage System: 32GB industrial-grade SSD comes standard, while an optional 250GB www.honeywell-diver.com hard disk is provided to ensure safe data storage.

Network Interface: Supports Gigabit PROFINET (with built-in MRP redundancy) and Ethernet ports to provide high-speed data transfer capability.

Wireless communication: Optional WLAN function enables wireless communication through the internal Mini PCIe card holder.

Serial communication: RS-232 port (RJ-45) is provided to support serial communication needs.

Video/Graphic Interface: VGA port is supported for resolutions up to 2560×1440 @60Hz.

Audio: Provides micro DIN audio socket via IFP.

USB Interface: Provides two USB 2.0 standard ports for easy connection of external devices.

IV. Features of GE RXI Controller

Unique Intelligent Display Module: Provides configuration and maintenance functions for the controller without the need for additional software for easy operation.

High-performance control: Ensures efficient system operation through technologies such as high-performance dual-core CPU and Gigabit PROFINET.

Compact form factor: PROFINET-based design provides a small form factor solution for equipment manufacturers and *end users.

Highly Flexible Distributed I/O Functionality: Supports a variety of expansion slots to meet a wide range of industrial automation needs.

High Reliability: Adoption of industrial temperature grade components, combined with patented thermal monitoring technology and advanced passive cooling technology, ensures reliable operation in harsh environments.

V. Applications of GE RXI Controller

GE RXI controllers are widely used in various industrial automation systems, power systems and motor control, building automation and other fields. For example, in industrial automation systems, GE RXI controllers can be used to control the operation of mechanical equipment, sensors and actuators, realizing automated production and process control; in power systems, they can be used to protect and control circuits, monitor current and voltage, and prevent the occurrence of electrical faults; in the field of construction, they can be used in building automation systems, such as lighting control and air-conditioning control, to improve energy efficiency and comfort.

VI. Summary

GE RXI controller has become a star product in the field of industrial automation with its excellent performance, rich functions and stable operation.

GE Fanuc IC200ERM002 Non-Isolated Expansion Module

The GE Fanuc IC200ERM002 Non-Isolated Expansion Module is a product of GE Intelligent Platforms/GE Fanuc.

It is manufactured as part of the Versamax series to enhance the functionality of a PLC or I/O output station and increase the number of modules that can be connected.

About the IC200ERM002

The GE Fanuc IC200ERM002 module is a non-isolated expansion receiver module that is part of the Versamax family.

This expansion module is used to enhance the functionality of a Versamax PLC or I/O output station and also increases the number of modules that can be connected.

The IC200ERM002 Expansion Module has a **capacity of 7 racks with up to 8 modules per rack*.

It requires an installed power supply to power all connected devices.

When an additional power supply or booster carrier is used, it should be connected to the mains power supply on the IC200ERM002 Expansion Module.

It also features 3 on-board LEDs to indicate the operational status of the device.

The module can also be used as a single-ended or multi-rack Versamax I/O expansion system.

Where the module is used in a multi-rack implementation, the total cable length cannot exceed 50 feet or 15 meters.

When the Versamax GE Fanuc IC200ERM002 Non-Isolated Expansion Receiver Module is used in a single-ended system with only 1 expansion rack, the

The cable length should not exceed 3.3 feet or 1 meter.

It has a data rate of 2.765 Mbps or 5 Mbps, depending on the implementation used.

The GE Fanuc IC200ERM002 expansion module is equipped with two 26-pin D-shell expansion female ports.

In addition, it has two different current consumption ratings with a 3.3 volt or 5 volt backplane rating.

When the backplane voltage is 5 volts, the current consumption is rated at 70 milliamps and when the backplane voltage is rated at 20.3 volts, the current consumption is rated at 3 milliamps.

GE General Electric IC200MDD841 High-Speed Counter Module

The IC200MDD841 high speed counter module is a GE Fanuc product.

This module is manufactured as part of the VersaMax product line.

It has mixed discrete I/O points with 12 positive logic outputs and 20 positive logic inputs and is also configurable.

About the IC200MDD841

The IC200MDD841 module is a high-speed counter module manufactured by GE Fanuc.

It is part of the Versamax series and has mixed discrete inputs and outputs, including 12 positive logic outputs and 20 positive logic inputs, some of which are configurable.

Devices connected to these I/O connectors have two states: on and off.

The GE Fanuc IC2MDD200 module has no protection features, such as internal fuses or isolation of individual channels.

It supports a variety of input and output configuration settings, such as pulse-width modulation, ramp pulse train, pulse train, and high-speed counters.

When this module is set to its default configuration,www.honeywell-diver.com it has 841 Type A high-speed counter outputs and inputs.

These high-speed counters process pulse signals at 4 kHz. In addition, in the default configuration, the module has 80 standard outputs and 8 standard inputs.

The backplane powers the GE Fanuc IC200MDD841 high-speed counter module, but a separate power supply powers all external output devices.

When the module is connected to a backplane power supply rated at 5 volts, it draws 30 milliamps of current.

The inputs and outputs of the IC200MDD841 module operate at 24 volts DC.

The module’s on/off state current ratings are 3 to 8 mA/0 to 0.5 mA, respectively.

It measures 66.8 mm or 2.63 inches long, 110 mm or 4.3 inches wide, and 50 mm or 1.956 inches deep.

The high-speed counter module provides error detection and displays up to 13 words of status data.

It has on-board LEDs that display device status information.

Parker AC Variable Frequency Drives HP Rated-AC30 Series

Description

The AC30 variable speed drive has been designed to provide users with exceptional levels of motor control, from simple open-loop pumps and fans through to closed-loop process line applications.

The AC30 combines advanced performance with exceptional ease of use, making even the most complex applications simple to achieve.

Working with the five principles of Flexibility, Simplicity, Reliability, Connectivity and Capability our engineers have created a product focussed on making the benefits of quality motor control available to every business.

Parker provides easy to use software tools for all levels of experience; enabling users to address any application. Simple applications can be setup in seconds and more complex applications can be configured in the simplest and most logical way.

Programming can be via the keypad, DSELite, Parker Drive QuickTool software or the Codysys based Parker Developer with full IEC 61131 PLC Functionality.

The AC30 provides users with access to a large library of application macros and worked examples. While users are free to develop their own applications, they can also save time and development cost by accessing and customising  examples of completed solutions.

To enable connectivity into a wide range of automation systems the AC30 features Profinet and Ethernet IP through dual Ethernet ports, as well as Modbus TCP IP with client and server functionality.

That makes the AC30 series compatible with more than 80 percent of automation architecture; there is no need for expensive add-ons or upgrade modules.

The Ethernet protocols also provide potential for intelligent data analytics and connection to external servers – opening up links to the cloud or big data

functionality.

So whether for standalone use or for integration into a complex automation system, www.honeywell-diver.com the AC30 offers an easy to use solution for both simple and advanced motor control applications.

Technical Characteristics – Overview

Designed with you in mind

Flexibility

A fully featured list of standard functionality along with the use of common control and option modules allows users to put the drive to work in many different open- or closed-loop applications.

Simplicity

From the clear and concise backlit LCD display to the easy to use programming software, AC30 has been engineered to make the process of commissioning, operating and maintaining the drive as easy as possible.

Reliability

Parker engineers have taken every possible step to reduce the likelihood of problems occurring, including a number of features in the AC30 that will ensure any loss of productivity is minimised and production restarted as safely and as soon as possible.

Connectivity

Its flexible and highly modular construction enables a wide range of communications and I/O modules to be easily added as required. This enables AC30 to be used in advanced applications including multiple drive configurations.

Capability

Integrated macros for a range of applications and PLC functionality enable more capable users to create sophisticated control that would previously have required a separate PLC. The AC30 can be integrated into even the most complex systems.

Compact footprint, chassis or through-panel mounting

• Multi-position feet with keyhole slots for ease of mounting

• Reduced heat radiation allows side-by-side mounting

Engineered cooling improves reliability

• Intelligent design minimises force ventilation requirements

• Removable fan improves maintainability

• Isolated power stack cooling path reduces contamination of control electronics

Unobstructed access to power and dynamic brake terminals

• Terminal covers removable with drive in-situ

• Dynamic brake switch fitted as standard

• Easy access to DC Bus connections

Suitable for harsh environments

• AC30 is conformally coated as standard and meets the requirements of environment classes 3C1, 3C2 (all defined substances) plus 3C3 and 3C4 for Hydrogen Sulphide (H2S)

• DNV marine / offshore approval

Suited to all environments

• Internal EMC filter options up to C2 1st environment for use in commercial buildings

• CE marked to EN61800-5-1 and NRTL listed to UL508C and C22.2#14

• DC link chokes above 2.2 kW reduce harmonics to below IEC/ EN61000-3-12 limits

Expandable I/O capabilities

• A range of option modules expand AC30 to accommodate application specific I/O

• High-performance, closed-loop control with pulse encoder or resolver feedback module

• Spring clamp terminals reduce installation time and risk of loose connections

Parker Variable Speed Drives – AC15 Series

Overview

Description

The AC15 Compact Drive is a simple to use, reliable and economical solution for every-day motor control applications that require speed or torque control in the power range of 0.37 kW to 30 kW (0.5 to 40 HP).

With compact dimensions and features normally only associated with higher specification drives, including Safe Torque Off, Ethernet communications,

sensorless vector mode for control of both Permanent Magnet (PMAC) and AC induction motors and a full 150 % overload for 1 minute, AC15 provides

an optimized solution for OEM machine builders looking for a compact, cost-effective drive without compromising on performance.

Simplicity

AC15 is designed to reduce the time and effort required to install, setup and commission through it’s easy to use integrated keypad and application

macros, or the powerful DSE Lite software tool and rich function block set. Minimal wiring requirements and easily accessed terminals make AC15 quick and

easy to install. Auto-tuning sensorless vector mode takes AC15 beyond simple V/Hz control allowing users requiring greater dynamic speed or torque control for their application to benefit from the drive’s enhanced speed and torque accuracy.

Reliability

Proven technology and manufacturing techniques ensure AC15 has been engineered and built to deliver consistently outstanding levels of performance day in, day out, ensuring maximum uptime and productivity.

Thanks to its conformally coated PC boards, AC15 is capable of withstanding class C3 environments, allowing you to operate AC15 with the utmost confidence in more applications.

Applications

AC15 provides a straight-forward approach to general purpose industrial motor control applications across a wide range of industries, giving users the benefits of the inherent energy-saving properties of using a variable speed drive, as well as the improved reliability and extended service life benefits associated with smoother starting and stopping of regularly cycling loads.

Typical applications for AC15 include…

• Conveyor

• Centrifuge

• Fans

• Mixers

• Packaging Machines

• Textile Machines

• Strapping Machines

• Labelling Machines

• Industrial Washing Machines

• Machine Tool Spindles

• Roller Doors

Parker AC890 Compact Modular System AC Drive

The AC890 is a compact, modular systems AC drive engineered to control speed and position of open-loop and closed-loop, single- or multi-motor AC induction or servo motor applications, up to 500HP.

The Ac890 is a compact, modular systems drive engineered to control speed and position of openloop and closedoop, single- or multi.motor Ac induction or servo motor applications. Compatilble with a wide range of feedback options, the Ac890 may be used with any ACmotor and virtually any speed/position feedback options. With this flexibility you may not even need to replace your existing Ac motor toachieve high performance, saving you time and money. The Ac890 is available in 380-460/500v 3-phase 0.75 to 500HP and 220v-240V 3phase 0.75 to 10HP.

Markets:

“Water and Wastewater Treatment

·Pulp and Paper

·Steel Mills

·Marine

·Cranes

.Wind and Solar Power

.Food and Chemical Processing

Features and Benefits.

The AC890 can be configured for 4 different modes of operation .

open-oop (volts/frequency) control

This mode is ideal for basic, single or multi-motor speed control.Sensorless vector controlWith its ultra high performance sensorless vector algorithm,the Ac890 delivers a combination of both high torgue and close speedregulation without the need for any speed measuring transducer.Closed-loop vector control

Full closedloop flux vector performance can be achieved with the Ac890 by simply adding an encoder feedback ‘technology box. Thisprovides 1 00% continuous full load standstilltorque, plus a highly dynamic speed loop more than suficient for the most demanding applications.

4 Quadrant active front-end power supply moduleharmonic content is achieved (THD< 3%)

With this confauration, the eneray is fed back into the mains supply with sinusoidal currents and unity power factor a very low curen

Applications:

.Slitting Lines

.Hot and Cold Saws

.Forming Rolls

.Printing Lines

.Fans, Pumps, and Blowers

.Water Treatment

.Wind Turbines

.Solar Power

.Engine Testing

.Gearbox Testing

A-B 1336E-B075-AE-EN-HA2-L6 Adjustable Frequency Drive

Allen-Bradley/Rockwell Automation 1336E-B075-AE-EN-HA2-L6 Frequency Drives

is designed and manufactured as an adjustable frequency inverter within the 1336 IMPACT inverter series.

It uses its adjustable frequency to increase or decrease the speed and torque ratings of motors in Allen-Bradley/Rockwell Automation PLC systems.

The 1336E-B075-AE-EN-HA2-L6 adjustable-frequency drive produces up to 75 hp of nominal output power during operation.

It supports multiple start options, such as an automatic start option and a flying start option.

The 1336E-B075-AE-EN-HA2-L6 Adjustable Frequency Drive also features non-volatile parameter storage, a programmer/controller HMI with digital potentiometer, and a 115 VAC control interface.

The 1336E-B075-AE-EN-HA2-L6 drive is a 1336 IMPACT drive manufactured by Allen-Bradley.

It is rated at 380 to 480 volts AC, 56 kilowatts and 75 horsepower.

It is equipped with a programmer/controller with digital potentiometer HMI to simplify drive control and programming.

Up to 16 programmable speed command transitions are available on the drive, which supports SCANport communications and English as the programming language.

The 1336E-B075-AE-EN-HA2-L6 IMPACT drive is designed to provide unrivaled speed control.

The diagnostic features on this drive allow real-time monitoring of its logic board and power structure.

It has 32 entry fault queues and 32 entry warning queues with markers for clearing faults and timestamping power-ups.

Flying start mode on this drive applies to motors that are already spinning loads.

As with all B-frame 1336 IMPACT drives, the 1336E-B075-AE-EN-HA2-L6 drive does not support network connectivity through an isolated gateway.

Its memory storage is non-volatile, and it has a NEMA 1 (IP20)/EMC enclosure and a 115-volt AC control interface.

The function blocks on this drive provide greater flexibility than other drives.

Connecting the 1336E-B075-AE-EN-HA2-L6 IMPACT Drive to a Motor Using a Long Cable

Cable terminators or output chokes may be required to minimize voltage reflections at the motor terminals.

It can be fitted with different types of cables including shielded, unshielded and armored cables.

The drive is designed to use a three-phase power supply that is symmetrical to www.honeywell-diver.com ground and supports the use of a line reactor or isolation transformer if the power supply encounters power line conditions that could cause a fault.

This 1336 PLUS II adjustable frequency AC drive is a 380-480VAC unit with 56 (75) kilowatts (kW) of power (horsepower) and has an (n) NEMA 1 (IP20)/EMC enclosure.

Related Product Recommendations:

IC660TBD024K GeniusI/O Terminal Assembly Module

1769-OF2 Analog Output Module

SK-G9-GDB1-D292 Medium and High Voltage Inverter Cooling Fan Motherboards

1756-IF4FXOF2F ControlLogix Discrete High-Speed Analog I/O Module

5205-DFNT-PDPS EtherNet/IP to PROFIBUS DP Slave Gateway

IC200ALG327H 12-Channel 13-Bit Voltage Analog Output Module

5X00419G01 Ethernet Link Controller

1336-BDB-SP6C GATE DRIVER BOARD

1769-L30ER Dual Ethernet Controller Device

HE693THM884M Thermocouple Input Module

D2D160-BE02-11 AC Centrifugal Fans Cooling Fan Assembly

Search for products

Back to Top
Product has been added to your cart