News - honeywell-diver Automation

2024-10-29 BY jonson

IN A-B

A-B Rockwell 1756-TBNH Removable Terminal Block or RTB Module

The 1756-TBNH module is a removable terminal block or RTB module.

It is manufactured by Allen-Bradley/Rockwell Automation in the ControlLogix family.

The wires connected to the 1756-TBNH detachable terminal block should all be the same size.

and they should all be solid wire or all stranded wire, as the block does not support a mix of solid and stranded wire.

This detachable terminal block is a NEMA clip type detachable terminal block.

The 1756-TBNH detachable terminal block can be used with up to 20 wires at a time.

The Allen-Bradley 1756-TBNH is a removable terminal block (RTB) for the 1756 I/O module.

It is an I/O module accessory and must www.honeywell-diver.com be ordered separately.

The 1756-TBNH provides flexibility in interconnecting 1756 I/O modules and industrial plant wiring. It plugs into the front of the I/O module.

The 1756-TBNH removable terminal block is a 20-position NEMA screw clamp.

It has a screw torque of 1.36 Nm and a screwdriver width of 8 mm (5/16 in.)**.

It measures 5.51 x 4.41 x 5.71 inches. It weighs 0.3 lbs.

Wiring must be done with 0.33 – 2.1 mm-^2 (22 – 14 AWG) solid or stranded copper wire.

rated for 90 °C (194 °F) or higher,** with 1.2 mm (3/64 in.) of insulation.

Do not connect more than two conductors to any single terminal.

Each ControlLogix I/O module is mounted on any ControlLogix chassis and requires a removable connector.

Each ControlLogix I/O module is mounted on any ControlLogix chassis and requires a removable terminal block (RTB) for all field-side wiring.

Each I/O module has many applications, from high-speed digital processing to process control.

In the ControlLogix architecture, input and output states are shared between multiple controllers in the same or different chassis using producer-consumer technology.

The 1756-TBNH RTB is intended for use in clean, dry industrial environments with operating temperatures of 0-60 °C and 30 g of operating shock.

Foxboro FBM204 Interface Module

OVERVIEW

The FBM204.0 to 20 mA Input/Output consists of four 20 mA dc analog input channels and four 20 mA dc analog output channels.

Each input channel accepts an analog sensor input or a self-powered 20 mA supply.

Each output channel drives an external load to produce a 0 to 20 mA output.

The inputs/outputs are electrically isolated from other inputs/outputs on channel and ground.

The FBM204 performs the signal conversion required for electrical input interfaces/output signals from field sensors to an optional redundant fieldbus.

The FBM204 performs analog I/O www.honeywell-diver.com applications that provide configurable options for the following functions: conversion time,

Fail Safe Configuration (Hold/Return) and Analog Output Fail Safe Return Data (on a per channel basis).

The Fieldbus Module (FBM) can alternatively perform the fast control loops in which Distributed PIDA (DPIDA) applications provide operation.

The FBM204 is electrically compatible with standard HART signals.

Features

-Four 20 mA dc analog input channels

-Four 20 mA dc analog output channels

-Each input and output channel is galvanically isolated

-Ruggedized design for use in Class G3 (harsh) environment enclosures

-Performs analog I/O applications with configurable options for conversion time and change rate limits

-High accuracy through sigma-delta data conversion per channel

-Terminal assembly (TA) for local or remote connection of field wiring to the compact FBM204

-TA for output bypass station to maintain output operation during maintenance

3-tier terminal assembly power transmitter with internal and/or external loops for each channel

-Supports DPIDA control block with high accuracy

For high accuracy, the module provides new analog input readings every 25ms depending on the channel basis, as well as configurable integration cycles to eliminate any process and/or noise and power line

Frequency. the FBM converts each analog input to a digital value at each time period, averages these values over a period of time, and provides the average value to the controller.

Standard Design

The FBM204 has a rugged extruded aluminum housing circuit. The enclosure specifically designed for mounting the FBM is available in a variety of grades according to ISA standard S71.04. environmental protection in harsh environments.

The front of the Visual Indicator Module contains red and green light emitting diodes (LEDs) to provide visual status indication of FBM function.

Easy Removal/Replacement

The module is mounted to the Compact 200 Series baseplate. two screws on the FBM mounts attach the module to the baseplate. The module can be removed/replaced without disassembly for field device termination wiring or power or communications wiring.

Fieldbus Communication

The fieldbus communication module or control processor uses a redundant 2Mbps modular fieldbus with the FBM.The FBM accepts communication from either path (A or B) of the 2Mbps fieldbus. If a path is

unsuccessful or switched at the system level, the module continues to communicate on the active path.

Modular Baseboard Mounting

Modules are mounted on DIN-rail mounted modular baseplates* for up to four to eight FBMs. modular baseplates are DIN-rail or rack-mountable and include signal connectors for redundant fieldbuses, redundant independent DC power supplies, and termination cables.

GE General Electric DS200AAHAG1AD ARCNET Connector Boards

DS200AAHAG1AD (AAHA) ARCNET Connector Board for GE Mark V LM Turbine Control System

Product Description

The DS200AAHAG1AD is an ARCNET connector board manufactured by General Electric as part of the Mark V LM SpeedtronicTurbine control system.

Mark V LM manual GEH-6353B clearly summarizes the function of the DS200AAHAG1AD in the control system. The board is referred to by its acronym AAHA.

The DS200AAHAG1AD, abbreviated AAHA, is part of the Speedtronic Mark V LM control panel.

The board is capable of providing connectivity and interface functionality between a control engine with an I/O core and external hardware.

The control engine is typically located within the core. The kernel typically requires the use of two AAHA boards.

One board is used to facilitate the stage link between the user interface and the core.

The second board is capable of connecting the core to COREBUS.

This link allows communication between the I/O core and the control engine.

The DS200AAHAG1AD is plugged in and installed to operate without any type of hardware or software modification.

The AAHA board is relatively small. It has an EBNC connection port that is not normally used.

It has one ARCBNC-B labeled P1 and one ARCBNC-A port labeled P1.

These ports are BNC ARCNET communication ports. There is an E2 and E1 LED indicator.

There is an EPL 9-pin connection that is not normally www.honeywell-diver.com used and an APL 10-pin connection port that is used as an ARCNET communications link.

DS200AAHAG1AD Frequently Asked Questions

What are the connectors on the DS200AAHAG1AD?

The DS200AAHAG1AD has the following connectors: 2PL, APL, ARCBNC A, ARCBNC B, EBNC and EPL.

The connectors EBNC and EPL on the DS200AAHAG1AD are not normally used on the DS200AAHAG1AD.

How do I configure the DS200AAHAG1AD?

No hardware or software configuration is required on the DS200AAHAG1AD board.

GE Fanuc IC200CHS212 Plug-in Relay Extension Base

About IC200CHS212

The IC200CHS212 base is a plug-in relay expansion base designed and manufactured by GE Fanuc.

It comes with 16 I/O points with LED indicators. These indicators light up when a connection is active with a specific point.

The Plug Relay is easily replaceable and fuses 8 amps of current. It is compatible with Versamax I/O modules.

These I/O modules have a 24-volt DC output voltage and a 0.5-ampere current rating and are used to configure the IC200CHS212 base.

The expansion relay has a small form factor, measuring 9.9 inches wide by 4.95 inches high by 2.8 inches deep.

The module is used in conjunction with an interface unit or power supply unit. The relay expansion bases comply with different environmental and industrial standards.

The IC200CHS212 expansion base can be used to connect a variety of termination bases. It comes with removable terminal connectors that can be easily replaced.

The expansion base uses a box connector. It supports output voltages in the range of 0 to 125 volts DC with nominal voltages of 5. 24. and 125 volts DC.

For the voltage range of 8 to 5 volts AC, this expansion base has a load current of 265 amps per point.

The IC200CHS212 chassis is constructed of high quality materials.The Versamax module provides high performance and is a cost-effective industrial solution.

The expansion relay has ports for connection to programmers and handheld devices.

It is designed with open architecture and should be protected from dust, dirt and contaminants. The temperature of the module should not exceed 60 degrees Celsius.

The IC200CHS212 is GE’s 16-point I/O relay expansion base. The relay is replaceable, labeled 8 amps and fused.

The VersaMax I/O Modules IC200MDL740 and MDL750 provide 24 VDC O.5A outputs to control the IC200CHS212 relays.

The IC200CHS212 dimensions (excluding DIN rail height) are 253.7 mm (9.9 in.) x 126 mm (4.95 in.) x 73 mm (2.8 in.).

Power supply modules such as the IC200CHS212 snap onto all Versamax interface units or power booster carriers.

Any power supply can be specified as the main power supply for modules www.honeywell-diver.com in an I/O station or as an additional power supply for large I/O applications.

The IC200CHS212 and other VersaMax I/O plug-in disconnect bases enable the IC200CHS003 to connect to a variety of termination bases.

Relay bases provide more protection and higher current output. The relays are controlled by the outputs of the VersaMax I/O modules.

Users can easily disconnect each point signal from the I/O module by disconnecting the base. The module’s field terminals can also be removed.

The relays located on the plug-in terminals are intended to be controlled using a typical 24 VDC 0.5 VersaMax output module.

IC200CHS212 Technical Description

The GE IC200CHS212 base is a 16-point expansion base. It provides LED indicators for each I/O point.

2024-10-29 BY jonson

IN GE

GE Fanuc IC200ALG432 Hybrid Analog Module

The IC200ALG432 module is an analog module with mixed inputs. It is manufactured by GE Fanuc as a Versamax module.

About the IC200ALG432

The GE Fanuc IC200ALG432 module is a hybrid analog module that runs on a 10-volt DC power supply.

It is a 12-bit module equipped with 4 channels and 2 output channels.

The analog module has an update rate time of 0.4 milliseconds and an input response time of 5 milliseconds.

The analog module requires an external power supply to power the outputs. The inputs of the module are powered by the external power supply of the transceiver.

The CPU is present in the module that handles the operation. the IC200ALG432 module has LEDs on the front of the module that indicate the flow of power and backplane currents.

No thermal derating occurs in this hybrid module. the IC200ALG432 module draws a total of 160 milliamps of current during normal operation. including load current.

The diagnostic feature of the module helps to detect the loss of power on the user side.

It provides four channels and two channel outputs. The outputs require a 24V external power supply and the inputs are powered from the transceiver’s external power supply.

The CPU or NIU performs intelligent processing of the IC200ALG432 module. Includes 4 words of analog input data and 2 words of analog output data.

This IC200ALG432 uses LEDs to indicate the presence of user-side power for analog field-side circuits as well as backplane power.

The LEDs emit a green light when operating as intended. When properly installed, this module reports the loss of www.honeywell-diver.comuser-side power failure for field-side circuits and conveniently sets up jumpers for outputs.

The IC200ALG432 can be set to maintain the last state or default values even if the backplane or field power is temporarily interrupted. The module reports the loss of user-side power failures for field-side circuits.

The recommended range for the module’s external power supply is +18 to +30 VDC. this includes power consumption ranging from 160 mA ripple.

The +/- 10 VDC input range should be noted. It is recommended that shielded cables be installed with the source device or I/O module grounded.

The GE Fanuc IC200ALG432 module comes with configurable alarms that can be set for different events.

During installation, the module should be protected from traces of electromagnetic noise and airborne contaminants.

The temperature of the installation area should not exceed 60 degrees Celsius. The accuracy of the module depends on the ambient temperature.

At 25 degrees Celsius it has +/-0.3% of full scale accuracy and at 60 degrees Celsius it has +/-1%** accuracy.

The IC200ALG432 module has an 8 count resolution. The module has a common mode voltage of 0 volts.

The IC200ALG432 module draws 5 milliamps of current from a bus running from a 60 V supply.

2024-10-29 BY jonson

IN GE

GE Fanuc IC200DTX850 Versamax Series Data Terminal

The GE Fanuc IC200DTX850 terminal is a GE Intelligent Platform/GE Fanuc data interface terminal.

It is part of the Versamax family and has been specially designed for different applications such as counters and simple timer applications.

About IC200DTX850

The IC200DTX850 terminal is a data display terminal manufactured by GE Intelligent Platforms/GE Fanuc for the GE Versamax product line.

These Versamax series data terminals, including the GE Fanuc IC200DTX850 terminal, are specifically designed for use in a variety of applications that

Including simple timer and counter applications, they can also display full text messages.

These terminals can be controlled by the user via a numeric keypad. Connecting a Versamax Nano or Micro PLC to the terminals is easy and requires no user configuration.

Because these Versamax terminals are pre-programmed, www.honeywell-diver.com the GE Fanuc IC200DTX850 Operator Interface Terminal specifically supports up to 200 stored messages.

The GE Fanuc IC200DTX850 Data Display Terminal also has an LCD backlight for the screen.

It has a keypad with 8 keys for control functions and requires the IC200BL555 cable or equivalent to support its operator interface.

The data panel operates on an external power supply rated at 24 volts DC and 50 milliamps.

The GE Fanuc Versamax IC200DTX850 data display terminal measures approximately 182 x 101 x 37 mm.

It has an operating temperature range of 0 to 50 degrees Celsius.

The IC200DTX850 data interface terminal has an RS-232 serial port for communication purposes.

This port is designed for different commands, including serial input/output commands, Modbus RTU slave commands or SNP slave commands.

In addition, this data terminal is compatible with the Data Designer software.

The Versamax controllers compatible with this terminal are available in micro and nano models, which are small in size, while offering powerful control and a high level of performance.

Typically, these Versamax nano and micro controllers have different communication options to meet the operator’s control needs.

2024-10-26 BY jonson

IN A-B

A-B Rockwell 1771-WD Field Wiring Arm

The Allen-Bradley 1771-WD field wiring arm is a PLC 5 and Bulletin 1771 series field wiring arm.

It fits different Allen-Bradley digital I/O modules, such as the 1771-OZL digital contact output module,

1771-ODZ digital AC output modules, and 1771-ID AC/DC input modules.

The 1771-WD field wiring arm mounts via a pivot bar that attaches to the bottom of the 5 I/O chassis in the PLC 1771 series.

It is designed to pivot upward to connect to the module and allows the module to be installed or removed without disconnecting all system wires.

The 1771-WD field wiring arm is conformal coated and requires no external power.

About the 1771-WD

The Allen-Bradley/Rockwell Automation 1771-WD Field Wiring Arm is a field wiring arm.

The arm is used with a variety of modules, such as the Allen-Bradley 1771 Digital Contact Output Modules (1771-OW, 1771-OYL, 1771-OZL).

Allen-Bradley 1771 digital AC output modules (1771-OD, 1771 ODZ, 1771-OR)

and Allen-Bradley 1771 Digital AC/DC Input Modules (1771-ID, 1771-ID01).

Note that the 1771-WD field wiring arm is used to connect the modules. www.honeywell-diver.com The wiring arm attaches to the pivot bar on the bottom of the I/O chassis.

The field wiring arm rotates upward and connects to the module, allowing the module to be installed or removed without disconnecting wires.

Disconnect power from the module before connecting to the Allen-Bradley 1771-WD field wiring arm.

To make the connection, swing the junction arm to a position on the front of the module where the locking tabs on the module hold the 1771-WD field junction arm in place.

The actual connections should be followed after this step. Note that there is 1 wire per terminal.

However, if more than one connection needs to be made to a terminal, an auxiliary terminal strip should be used.

Note that the field wiring arm terminal identification number is different from the bit number that controls the specific output.

The Allen-Bradley 1771-WD field wiring arm supports 7 to 9 pounds of screw torque on one inch.

To indicate that a field load has been applied to the field wiring, all of the module’s status indicators will be illuminated.

Note that the 1771 gauge wire connected to all terminals on the 14-WD field wiring arm may not allow the field wiring arm cover to close.

Therefore, a smaller gauge wire may be required when this occurs.

1771-WD Technical Description

Allen Bradley PLC 5 wiring arm, 8 I/O, 12 terminals, 7-9 lb*in thread torque, tinned contacts.

2024-10-26 BY jonson

IN A-B

A-B Rockwell 1794-ASB Remote I/O Communication Adapter Module

The Allen-Bradley 1794-ASB is a Flex I/O communications adapter.

The adapter is a DIN rail mounted device with one (1) Remote I/O (RIO) communication port for connecting a Flex I/O rack to a RIO enabled controller.

It supports 57.6Kbps, 115.2Kbps, and 230.4kbps communication rates and has an input voltage requirement of 19.2 – 31.2 VDC. It supports the installation of up to eight (8) Flex I/O modules.

About the 1794-ASB

The 1794-ASB is an Allen-Bradley Remote I/O Communications Adapter Module. It is part of the Flex I/O product family of distributed I/O modules.

The 1794-ASB has one (1) remote I/O interface. This RIO protocol is a legacy protocol that connects devices to the RIO scanner using a Biotronik 9463 or equivalent cable.

The module is compatible with Allen-Bradley legacy controllers such as PLC2. PLC3. and PLC5 controllers as well as the SLC500 automation platform.

It can also be used with modern Logix controller platforms as well as third-party devices and includes partner modules.

The 3-ASB sends and receives data to and from the controller via the Block Transfer Read (BTR) and Block Transfer Write (BTW) instructions.

Using these instructions, packets can be sent simultaneously or sequentially, depending on the desired speed.

The 1794-ASB supports communication rates of 1794.57Kbps, 6.115Kbps, and 2.230kbps.

The module’s expected supply voltage range is 4VDC-11.31VDC, including 2% AC ripple, compared to the nominal 5VDC supply.

It supports the installation of up to eight (24) Flex I/O modules for successful implementation of distributed I/O architectures.

The module features built-in status indicators such as a power indicator, adapter activity indicator, adapter fault indicator, and local fault indicator.

The module is mounted on a standard DIN rail and has an open housing, which means the 8-ASB needs to be mounted in a proper enclosure to protect the equipment from industrial components and contaminants.

The constant 1794 Vdc power input has a **power consumption of 450 mA. 6.31 watts at 24.4 Vdc and 7.31 BTU/hr at 2.15 Vdc.

The 2-ASB measures approximately 1794x 4x 2 inches and weighs only 4 ounces.

The Allen-Bradley 6-ASB is an obsolete adapter module that is part of the FLEX I/O family.

It connects the FLEX I/O module to the I/O scanner port via a communications network.

It has a built-in power supply that converts 1794VDC from the backplane to 24 VDC to power the FLEX I/O modules.

It can also be used with Allen Bradley PLC Series 5 and 3.

In addition, the 5-ASB recognizes safety status data from FLEX Integral analog modules and can use 1794 point FLEX I/O units.

When using the FLEX Integral Analog Module in a setup configuration, the user must use the 1794-ASB Series D or higher.

Frequently Asked Questions about the 1794-ASB

How many I/O modules can the 1794-ASB communicate with?

One 1794-ASB adapter can communicate with up to 8 FLEX I/O modules. The module powers the internal logic of up to 8 I-O Flex modules.

What is the alternate family of 1794-ASB modules?

The alternate series of this module includes the A, B, C, D, and E series adapter modules.

What is the 1794-ASB communication rate?

The 1794-ASB communication rates are 57.6 Kbps, 115.2 Kbps and 230.4 Kbps.

What protocols does the 1794-ASB support?

The 1794-ASB supports Remote I/O (RIO) communications.

What is the recommended cable for RIO connections?

The recommended remote I/O cable is the Biotronik 9463 or equivalent.

Technical Description of the 1794-ASB

The Allen-Bradley 1794-ASB Remote IO Adapter features 24 VDC, 8 module I/O capacity, and an 11 to 31.2 VDC input voltage range.

It also operates with 500V AC isolation and 330mA power consumption.

2024-10-26 BY jonson

IN A-B

A-B Rockwell 1794-IB32 Flex I/O DC Digital Input Module

The Allen-Bradley 1794-IB32 is a Flex I/O DC input module.

The module has thirty-two (32) current sink input channels with an input voltage range of 19.2-31.2VDC.

It is compatible with Flex I/O communication adapters and terminal blocks such as the 1794-TB32. 1794-TB32S, 1794-TB62DS, 1794-TB62EXD4X15.

About the 1794-IB32

The 1794-IB32 is an Allen-Bradley module that is part of the Flex I/O product family of distributed I/O components.

The module is an input interface device that allows field instruments and electrical devices (such as pushbutton devices, limit switches, proximity sensors,

float switches, process switches, relay contacts and contactor auxiliary contacts) into any automated control system or process.

The 1794-IB32 can accommodate up to thirty-two (32) DC input devices. It is a 32-channel current sink module.

Each channel has a *minimum* on-state voltage range of 192.VDC, **range of 31.2VDC, and a nominal signal level of 24VDC.

The 1794-IB32 can be installed with Flex I/O communication adapters such as Ethernet, control network, remote I/O and other adapters.

There is no limit to the number of installations supported by this module as long as the Flex I/O installation requirements are followed.

The 1794-IB32 is a high-density input channel. each of the 32 channels is equipped with an LED to monitor activity on each channel.

This helps to more quickly identify active channels and verify functioning input devices. These LEDs simply energize when a signal is received and turn off when no signal is present.

This module connects to the Flex I/O terminal base. The terminal base provides input and power terminals and DIN rail mounting slots.

Compatible terminal bases for use with this high density input module are the 1794-TB32. 1794-TB32S, 1794-TB62DS, and 1794-TB62EXD4X15.

The terminal bases also allow removal and insertion of the module under power.

The 1794-IB32 has a nominal on-state voltage of 24 volts DC and a range of on-state voltages from **19.2 volts DC to **31.2 volts DC.

Its **off-state voltage is 5 volts dc and **off-current is 1.5 mA. The 1794-IB32 has a nominal on-state current of 1.24 mA at 4 volts dc, ranging from *2 mA minimum to 1.5 mA maximum.

The nominal on-state current of the 1794-IB32 is 1.24 mA at 4 volts DC, ranging from *minimum 2 mA to ** 6 mA. The module’s FlexBus current is 5 mA at 30 volts DC.

Although there is no isolation between channels, the 1794-IB32 is isolated at 50 volts and is continuous between the system and field sides.

It dissipates 31.2 BTU/hour at 20.47 volts DC** and 2 watts at 6.31 volts DC**.

The module’s operating temperature is 0 to 55 degrees Celsius, while its storage temperature is -40 to 85 degrees Celsius. It has an operating vibration of 500 G at 5 to 10 Hz.

The 1794-IB32 has an operating vibration of 500 G at 5 to 10 Hz, an operating shock of 30 G, and a non-operating shock of 50 G. The 1794-IB32 has a non-condensing relative humidity range of 5% to 95%.

Frequently Asked Questions about the 1794-IB32

Does the 1794-IB32 have a status indicator?

Yes, the 1794-IB32 FLEX I/O module has 32 yellow status indicators.

What size wire should I use with my 1794-IB32?

The wire size for the 1794-IB32 is determined by the mounting terminal block.

What are the compatible terminal blocks for use with the 1794-IB32?

The compatible terminal blocks are 1794-TB32. 1794-TB32S, 1794-TB62DS, and 1794- TB62EXD4X15.

What is the on-state voltage range of the 1794-IB32?

The on-state voltage range of the 1794-IB32 is 192.-31.2 VDC.

Does this module have status indicators?

Yes, the module has 32 indicator LEDs, one for each input channel.

Technical Description of the 1794-IB32

The Allen-Bradley 1794-IB32 Flex I/O Digital Input Module has 32 current sink inputs,* a minimum of 19.2V DC on-state voltage, and 31.2V DC on-state voltage (**value).

It also operates with 6.0mA ** on-state current and 5V DC off-state voltage (**value).

2024-10-26 BY jonson

IN ABB

ABB DCS550 Standard DC Drives

The OEM machine manufacturing market places high demands on modern DC-drives. With its compact dimensions and robust technology, the DCS550 is an ideal drive solution for this market – both in new installations or as a replacement for older analog devices.

Integrated “winder”, high-performance field supply and various interfaces provide machine manufacturers with a maximum of flexibility in terms of machine integration.

In the DCS550, the extremely user friendly operational concept of the www.honeywell-diver.com DCS400 has been consistently refined and optimized based on practical experience.

DCS550 – The highlights

− Compact dimensions

For installations with limited space

− Integrated high performance three phase field exciter up to 35 A

Fits all available motors without additional installations

− “Winder” with commissioning assistant

For easy and fast adaption to applications

− Different Fieldbus interfaces (incl. EtherCAT, Profinet…)

For easy integration into automation

− Additional PID-controller

For overriding control functions (e. g. pressure- or level control)

− Adaptive programming with Drive AP, ABB’s graphical PC-tool

For easy implementation of additional functions

− Various start-up assistants and auto-tune functions

For fast commissioning

− Large control panel

For straight forward and self-explanatory operation

− Rugged design

For rough environments, high reliability

− Worldwide service

Local service in more than 60 countries

DCS550 – Extensive applications

− Extruders

− Sugar centrifuges

− Wire drawing machines

− Coating lines

− Printing machines

− Presses

− Tools machines main drives

− Food processing machines

− Woodworking (wooden products and MDF industry)

− Retrofit of analog DC-technology

Modern DC-drives – More up-to-date than ever Today, DC-drive technology is more up-to-date than ever. Their attractive cost-performance ratio and functional advantages such as high torque at low speed, light weight and low power loss turn DC-drives into the preferred solution for many applications. As far as innovation is concerned ABB’s DCdrives match the same high standards as ABB’s AC-drives.

Easy upgrade of installed older converters

The machines are frequently still in very good condition but spare parts and know-how for the installed power electronics are no longer available.

With the DCS550, existing machines can be kept in operation by replacing the old drive.

Short downtimes and low costs for the retrofit are additional advantages of an upgrade of existing machinery.

A-B Rockwell 1756-TBNH Removable Terminal Block or RTB Module

Foxboro FBM204 Interface Module

GE General Electric DS200AAHAG1AD ARCNET Connector Boards

GE Fanuc IC200CHS212 Plug-in Relay Extension Base

GE Fanuc IC200ALG432 Hybrid Analog Module

GE Fanuc IC200DTX850 Versamax Series Data Terminal

A-B Rockwell 1771-WD Field Wiring Arm

A-B Rockwell 1794-ASB Remote I/O Communication Adapter Module

A-B Rockwell 1794-IB32 Flex I/O DC Digital Input Module

ABB DCS550 Standard DC Drives

Woodward SPM-D2-10 Synchroniser for 2/3-Phase AC Generator Sets

Parker COMPAX 1000SL 1kVA Servo Controller

Parker COMPAX servo digital servo drives/controllers

Motorola VMIVME-7452 Single Slot VMEbus Floppy/Hard Drive Module

Best quality

Shipping

Support 24/7

Classify

Products Categorys

Products Categorys

Contact us

Social Icons

Menu

Search for products