Call us 24/7+86 15396212224
Call us 24/7+86 15396212224

News

Home / News (Page 2)
2024-12-20 BY
IN Motorola

Motorola MVME147S MPU VME Module

Features

The MVME147S features include

MC68030 microprocessor

Floating point coprocessor (MC68882)

Shared DRAM with parity (no parity on MVME147SRF)

Four serial ports with RS-232C buffers

Small Computer System Interface (SCSI) bus interface with DMA channel

Timer/calendar with battery backup

2K by 8 CMOS RAM with battery backup

Four ROM/PROM/EPROM/EPROM sockets (16-bit wide)

VMEbus interrupter

VMEbus system controller functions

VMEbus master interface (A32/D32. A24/D16 compatible)

VMEbus Requestor

SCON, DUAL, FAIL and STATUS status indicators

Reset and abort switches

Centronics Printer Port

Two 16-bit ticking timers for periodic interrupts

Watchdog timer

Ethernet transceiver interface (except MVME147SRF)

Cooling Requirements

Motorola VME modules are specified, designed, and tested to operate with forced air cooling from

Reliable operation over the incoming air temperature range of 0 degrees Celsius to 55 www.honeywell-diver.com degrees Celsius (32 degrees Fahrenheit to 131 degrees Fahrenheit).

Temperature qualification was performed in a standard Motorola VMEsystem 1000 chassis.

A 25-watt load board was inserted in two card slots, one on each side, adjacent to the board under test to simulate a high power density system configuration.

Three axial fans, each rated at 100 CFM, were mounted directly below the MVME card box.

The temperature of the incoming airflow was measured between the fan assembly and the card box, where the airflow first encountered the module under test.

The test software is executed when the module is subjected to a change in ambient temperature. The test software is executed when the ambient temperature changes.

Case temperatures of critical high power density integrated circuits are monitored to ensure that component supplier specifications are not exceeded.

While the exact amount of airflow required for cooling depends on the ambient air temperature as well as the type, number, and location of boards and other heat sources.

However, typically as little as 10 CFM of airflow through the module is sufficient for cooling.

In environments with lower maximum ambient temperatures, less airflow is required to cool the module.

Under more favourable thermal conditions, increased airflow will allow the module to operate reliably at ambient temperatures above 55 degrees Celsius.

It is important to note that in addition to the rated CFM of the air pusher, there are several factors that determine the actual amount of air flowing through the module.

FCC Compliance

These VME modules (MVME147S) have been tested in an FCC-compliant enclosure and meet the requirements for a Class A device.

FCC compliance is achieved under the following conditions:

Shielded cables are used for all external I/O ports

The cable shield is connected to ground through a metal-shell connector bonded to the front panel of the conductive module

Chassis rails are connected to earth ground

Front panel screws are tightened

The above conditions must be met in order to minimise RF emissions; failure to do so will affect the FCC compliance of the equipment containing the module.

General Description

The MVME147S is a dual-height VME module best suited for use in 32-bit VMEbus systems using both P1 and P2 backplanes.

It is a powerful module with large on-board shared RAM, a serial port, and a Centronics printer port.

The module provides a SCSI bus controller with DMA, floating point coprocessor, tick timer, and watchdog timer,

timer clock/calendar with battery backup, 2KB of static RAM with battery backup, four ROM slots, a serial interface, and a printer port.

In addition, the MVME147S provides 2KB of static RAM with battery backup, four ROM sockets, and an A32/D32 VMEbus interface with system controller functions.

The MVME147S can operate as part of a VMEbus system with other VME modules such as RAM modules, CPU modules, graphics modules and analogue I/O modules.

Related Product Recommendations:

DS200DSPCH1ADA Digital Signal Processor Control Board

IC660TBD024K Genius I/O Terminal Assembly Module

IC660TBD025 GeniusI/O Terminal Assembly Module

IC687BEM713B Fanuc 90-70 Series Bus Transmitter Unit

DS200KLDBG1ABC DS215KLDBG1AZZ03A Automation Module

DeltaVrm VerticalPlus Input/Output Subsystem carrier

DS200LDCCH1AGA Drive Control/LAN Communication Boards

DS200LDCCH1ALA Drive Control/LAN Communication Board

IC660ELB912J Gas Turbine Control System

8115-DO-DC 8-Channel Digital Output Module
2024-12-20 BY
IN ProSoft

Prosoft PTQ-PDPS PROFIBUS DP Slave Network Interface Module for Quantum

The PTQ-PDPS PROFIBUS DP Slave Communication Module allows compatible processors to connect easily with PROFIBUS DP master devices.

The PROFIBUS DP slave protocol driver supports PROFIBUS V0 slave implementations.

Provides robust data transfer between the module and the processor.

User-configurable data mapping and DP port operation make the interface an easy-to-use and powerful data transfer tool.

The PTQ module’s configuration/debug serial port connects a PC to the module for configuration, status, monitoring and troubleshooting (serial cable shipped with product).

After editing on the PC, the configuration file is downloaded and stored on the PTQ module.

PROFIBUS DP slaves have access to the input and output images of the device, with up to www.honeywell-diver.com 244 bytes of input and output data, for a total of up to 400 bytes.

The user can map these input and output data blocks into the module’s data memory for maximum flexibility and data transfer with other protocols.

Features Benefits

PROFIBUS DP-V0 slave protocol interface

 Adds PROFIBUS DP slave device monitoring to the network

 Simple configuration – GSD file available

 122 word input/122 word output, max. 200 word input/output

Licensed Backplane Technology  Manufactured under licence from Rockwell Automation®.

 High-speed data transfer between PTQ module and processor

 Installed as a generic 1756 module, includes ladder logic example

 View module data and status in RSLogix™ 5000 controller tags and UDTs

Includes ProSoft Configuration Builder software

 Graphical drag-and-drop configuration tool for simple module configuration

 Easy-to-use diagnostic window with menu-driven hardware and protocol diagnostics

 View module database contents via serial connection to a desktop PC

Backed by ProSoft technology

 20-year history of providing high-quality, reliable solutions

 Free, unlimited worldwide technical support over the phone, including pre-sales, setup or troubleshooting support, to help you get up and running quickly and stay up and running longer

 Three-year warranty to ensure reliability and protect against equipment failure

 Free ProSoft software tools are tightly integrated with our hardware …… Quick and easy total solutions to help you tailor our products to your application needs.

Configuration

ProSoft Configuration Builder (PCB) provides a PC-based software configuration solution that

for quickly and easily managing module configuration files, as well as viewing communications and network diagnostics.

PCB is a powerful solution not only for new configuration files, but also for importing configuration information from previous installations (known jobs) into new projects.

General Specifications

 Single slot – compatible with Quantum backplanes

 Module recognised as an option module with access to PLC memory for data transfer

 Configuration data is stored in the ProTalk® module’s non-volatile memory

 Modules are supplied with Microsoft Windows XP, 2000 and NT configuration software

 Up to four modules in one rack

 Local rack – modules must be placed in the same rack as the processor

 Compatible with all common quantum programming software packages, including Concept (version 2.6 or higher),

Unity Pro (2.2 or later), ProWORX (2.20 or later) and ModSoft.

 Supports quantum data types: 3x, 4x

 High-speed data transfer across backplane provides fast data update times

 Provides sample ladder files

Related Product Recommendations:

MMS6120 Dual Channel Bearing Vibration Measurement Module

D2D160-BE02-11 AC Centrifugal Fans Cooling Fan Assembly

D1961SH45T Rectifier Diode Industrial Robot Parts and Accessories

IC200ALG327H 12-Channel 13-Bit Voltage Analogue Output Module

IC200ALG260 Analogue Input Module

HE697RTM700B High Speed Counter Module

IC687BEM713B Fanuc 90-70 Series Bus Transmitter Unit

DS200KLDBG1ABC DS215KLDBG1AZZ03A Automation Module

DeltaVrm VerticalPlus Input/Output Subsystem carrier

8115-DO-DC 8-Channel Digital Output Module
2024-12-20 BY
IN A-B

A-B 1746SC-INO4I Analogue Pure Current Output Module

About the 1746SC-INO4I

The 1746sc-INO4I is Spectrum Controls’ analogue pure current output module. The module has four (4) isolated channel outputs.The 1746sc-INO4I occupies one slot in the 1746 Input/Output Chassis.The 1746sc-INO4I draws 120 milliamps of current from the backplane at 5 volts DC, but in order to minimise current loading on the backplane, the 1746sc-INO4I can be interfaced with an external power supply rated at 24 volts DC. The 1746sc-INO4I has a DIP switch that specifies whether the module is to be powered from the backplane or from an external power supply. When the DIP switch on the 1746sc-INO4I is set to the rack position, the module is powered from the backplane, and when the module is powered from an external 24 Vdc power supply, the DIP switch should be set to the EXT position.

The 1746sc-INO4I draws 5 volts DC from the backplane. This consumption rating is the same when the module is powered externally. The module has a removable 16-bit terminal block that accommodates Belden 8761 shielded twisted-pair cable. 1746sc-INO4I has 16-bit resolution, 366 nano-amps per count, and 320 microvolts per count. 1746sc-INO4I isolated channel analogue output models have auto-calibrating programmable limits and safety states, and are optically isolated for The 1746sc-INO4I isolated channel analogue output model has auto-calibrated programmable limits and safety states, and is opto-isolated to 750 volts DC (channel-to-channel, field wiring to backplane). 1746sc-INO4I is rated for thermal power dissipation up to 4.5 watts, with a maximum update time of 33.7 milliseconds for all 4 parallel channels, and a step response time of 1 millisecond. In addition, the 1746sc-INO4I is UL/CUL Class I, Division 2. Groups A, B, C, D, and CE listed.

Part number 1746sc-INO4I SLC 500 compatible module is an analogue output www.honeywell-diver.com module manufactured by spectrum control. This module is manufactured by Spectrum Controls, an Allen-Bradley partner.

Encompass Partners is an Allen-Bradley approved and certified partner to provide Allen-Bradley compatible products.

This module is similar in appearance to the actual SLC 500 module. The module has four (4) differential analogue output channels providing 0-20 mA, 0-21 mA, 4-20 mA at 366 nA per count with 16-bit resolution.The module features extended output ranges, auto-calibration, programmable limits, and safety status. The module’s data can be formatted into 16-bit binary, scaled engineering units, PID scaling, 1746-NO4 format, and user-defined proportional counts. Its accuracy is 0.08 per cent of full scale at 25 degrees Celsius and 0.15 per cent at 60 degrees Celsius.

Each channel of the module is galvanically isolated at 750 VDC, which improves system reliability by eliminating the noise crosstalk that occurs when converting the module’s high-resolution data. The same isolation level as the backplane field wiring provides protection for the rack and processor.

Since the module’s isolation eliminates the need for external signal isolation devices, system costs are reduced. The module’s single-slot width also saves critical chassis slots.

The module uses Allen-Bradley design and technology and functions like an Allen-Bradley module. Its configuration is similar to the SLC 500 module and most of its features are similar to the Allen-Bradley analogue output modules.

Technical Description of the 1746sc-INO4I

The Spectrum 1746sc-INO4I analogue output module has 4 channels and an analogue isolated current input type. It has 0-20 mA input current and 0-5V input voltage.

Related Product Recommendations:

Related Product Recommendations:

IC660TBD024K Genius I/O Terminal Assembly Module

IC687BEM713B Fanuc 90-70 Series Bus Transmitter Unit

DS200KLDBG1ABC DS215KLDBG1AZZ03A Automation Module

DeltaVrm VerticalPlus Input/Output Subsystem carrier

HE697RTM700B High Speed Counter Module

MMS6120 Dual Channel Bearing Vibration Measurement Module

8115-DO-DC 8-Channel Digital Output Module

D1961SH45T Rectifier Diode Industrial Robot Parts and Accessories

IC200ALG327H 12-Channel 13-Bit Voltage Analogue Output Module

IC200ALG260 Analogue Input Module Analog Input Module
2024-12-20 BY
IN A-B

A-B 1444-DYN04-01RA Measuring Module

Description:

The Allen Bradley 1444-DYN04-01RA module is part of the Allen-Bradley Dynamax family of intelligent I/O modules.

It is designed to provide the integrated and distributed solution needed to monitor and control critical industrial machinery.

The 1444-DYN04-01RA module monitors and protects pumps, motors, gearboxes, fans, gas and steam turbines, high-speed compressors, and other reciprocating or rotating machines.

About 1444-DYN04-01RA

The Allen-Bradley 1444-DYN04-01RA module is part of the Allen-Bradley Dynamax family of intelligent I/O modules.

It is used to provide the integrated and distributed solution needed to monitor and control critical machinery.

The 1444-DYN04-01RA module monitors and protects pumps, motors, gearboxes, fans, gas and steam turbines,

high-speed compressors, and other reciprocating or rotating machines. In addition to this, the 1444-DYN04-01RA module measures strain or pressure,

In addition, the 1444-DYN04-01RA module can also measure dynamic signals such as strain or pressure, vibration, and position measurement signals such as rod position, differential expansion or thrust.

The 1444-DYN04-01RA module allows real-time measurements to protect machinery from imminent failure.

In addition, the measurement results can be further processed to www.honeywell-diver.com calculate the acute fault indication parameters required to assess the current and predicted health of the machine.

The 1444-DYN04-01RA module can be managed and configured via a Logix controller and connected via an EtherNet/IP industrial network.

As with the rest of the Allen-Bradley/Rockwell Automation Integrated Architecture system, the

As with other parts of the Allen-Bradley/Rockwell Automation Integrated Architecture system, other system components such as visualisation products, controllers, and I/O products can be applied to the 1444-DYN04-01RA module to meet specific needs and applications.

Expansion modules for the 1444-DYN04-01RA module include a relay module, a tachometer signal conditioner and an analogue output module.

These modules can be configured and managed from either the master module or the host module 1444-DYN04-01RA.

The 1444-DYN04-01RA module as the host module can also report errors associated with any of the above expansion modules.

The 1444-DYN04-01RA module supports the EtherNet/IP communication protocol and has two RJ45 Ethernet ports.

These ports can be used either as a standard Ethernet connection (modules are connected to each other) or via DLR (Device Level Ring).

Related Product Recommendations:

IC660TBD024K Genius I/O Terminal Assembly Module

IC687BEM713B Fanuc 90-70 Series Bus Transmitter Unit

DS200KLDBG1ABC DS215KLDBG1AZZ03A Automation Module

DeltaVrm VerticalPlus Input/Output Subsystem carrier

D1961SH45T Rectifier Diode Industrial Robot Parts and Accessories

IC200ALG327H 12-Channel 13-Bit Voltage Analogue Output Module

IC200ALG260 Analogue Input Module Analog Input Module

HE697RTM700B High Speed Counter Module

MMS6120 Dual Channel Bearing Vibration Measurement Module

8115-DO-DC 8-Channel Digital Output Module
2024-12-20 BY
IN Emerson

Emerson DeltaV™ Smart Switches Plug and Play Industrial Switches

DeltaV™ switches are plug-and-play industrial switches with enhanced security features

New and improved hardware and software platforms with increased focus on security and improved performance

Fully managed by the DeltaV™ system

Automatically reports network alarms and diagnostic information to DeltaV workstations

Can be installed on the network between DeltaV workstations and Emerson’s Intelligent Firewall (DeltaV 2.5 network)

Plug-and-play installation

Automatic security lockout

Full range of industrial-grade fanless switches

Fully supported by Emerson

Introduction

The new DeltaV™ network “smart” switches are the next generation in the use of commercial off-the-shelf (COTS) components in control systems.

These switches combine the low cost of off-the-shelf components with www.honeywell-diver.com DeltaV-specified software and features that

making it more integrated and plug-and-play in the DeltaV Area Control Network (ACN) and other DeltaV networks outside the ACN.

The DeltaV Smart Switch requires no configuration to operate in a DeltaV network.

Access to advanced features requires minimal configuration and is easily accomplished using the DeltaV Network Device Command Centre.

This ensures that all Smart Switches on the network are configured consistently and securely, and that the performance of the DeltaV system is not compromised by misconfiguring any switch function.

This dedicated switch allows the DeltaV system to provide an advanced security feature of automatic port lockout, which can be easily implemented by the control system user.

Control system users can easily implement this feature: an increasingly important product feature in today’s harsh environments.

The DeltaV Smart Switch is also pre-configured to utilise features in the latest software releases, such as ARP sniffing and enhanced security features.

(The DeltaV Smart Switch is also preconfigured to detect certain man-in-the-middle attacks using features in the latest version of the software, such as ARP sniffing and enhanced port locking algorithms: ARP spooffng detection and enhanced port locking algorithms.

Benefits

Enhanced security. The new generation of DeltaV Smart Switches is based on a more powerful hardware and software platform with an increased focus on security.

The new hardware features powerful CPUs for control plane and management operations.

The software has many new features such as role-based access, secure user and password management, brute force attack protection, audit trails and user-readable event logs.

There is also a new HTML5 web interface that can be accessed through the Network Device Command Centre, making it easy to upgrade the switch software.

The next-generation switch also offers more flexible configuration options.

Improved performance. The switching ASICs used in these new products offer new capabilities

such as increased network buffers, the ability to process/forward/filter packets based on more L2 address information such as IP addresses, UDP or TCP ports, and a non-blocking architecture.

and non-blocking architecture, in addition to more powerful CPUs for control plane and management operations.

Fully managed by DeltaV. The DeltaV Switch Commissioning application automatically discovers the switch in the Network Device Command Centre (formerly the Smart Switch Command Centre) when the switch is started.

Network addresses are automatically assigned by DeltaV DCS or by the user when installed in a DeltaV 2.5 network (new in DeltaV v13.3).

Simply provide the switch name and description and select a few setup parameters and the switch will begin reporting. A serial connection is no longer required to configure the switch.

Automatic reporting of network alarms and diagnostics to DeltaV workstations. Operators and maintenance stations will automatically receive device alerts that indicate abnormal network communications.

The DeltaV Network Device Command Centre application provides an interface for diagnosing and troubleshooting network problems. All of this is built-in, eliminating the need for third-party applications for network monitoring.

Plug and Play Installation. The new generation of DeltaV Smart Switches feature a DeltaV-compatible setup that installs out of the box into a compatible DeltaV network.

They require no user configuration to fully support DeltaV network communications.

NDCC ensures that the configuration of all Smart Switches on the network remains consistent, so you never have to worry about misconfigurations affecting network performance.

Plug and Play requires that any existing switch or network device be configured for 100/1000 full-duplex communication or auto-negotiation.

Auto-lock prevents unauthorised network connections. Disabling unused network connections is a security “best practice” that helps you comply with factory security policies.

With the switch’s built-in one-click lockout feature, you simply click a button in the DeltaV Network Appliance Command Centre application to

to automatically lock all unused network ports on your system. Easily protect your network from intrusion.

The port locking algorithm has been enhanced to allow locking of multiple daisy-chained DeltaV nodes, as well as detection of new nodes within dynamically determined uplink ports.

You can also configure the switch to ignore lockdown commands on specific switch ports if the application requires it.

For example, a port connected to a virtualised host server to allow DeltaV VMs to move between hosts.

Accessing the Console. Secure Shell (SSH) and serial connections are provided using a USB-C cable (except for the RM2040).

The Advanced Configuration menu includes a handful of settings that allow you to customise the switch for your specific use case while conforming to the requirements of the DeltaV Regional Control Network.

SSH communications provide a secure connection to the switch console.

Encryption in SSH communications provides additional security for switch operation and maintenance by protecting user credentials and preventing interception.

Full range of switch hardware configurations. The new generation of DeltaV network switches offers a wide range of hardware solutions.

From 30-port rackmount units to ffxed-port DIN-rail switches, DeltaV network switches meet a wide range of network requirements.

The extensive line of DeltaV Smart Switches is all you need to implement a complete DeltaV control network.

Emerson provides full support. As an Emerson product, these DeltaV network switches are fully supported by Emerson when used in a DeltaV network.
2024-12-20 BY
IN Emerson

Emerson AMS 2140 Mechanical Health™ Analyser

Vibration analyser offers powerful user experience

AMS 2140 Machinery Health™ Analyser The AMS 2140 is the most comprehensive tool for assessing and predicting machinery health

The AMS 2140 builds on Emerson’s industry-leading CSI 2130 to make path-based maintenance more efficient and predictive diagnostics more practical.

predictive diagnostics more practical. the AMS 2140 is guided by human-centred design principles.

The AMS 2140 follows human-centred design principles and is user-focused to meet the availability and advanced diagnostic requirements of reliability engineers.

With more than 25 years of expertise in vibration analysis, Emerson’s portable analysers provide the most powerful user experience for predicting equipment problems.

Routes can be executed more efficiently with faster data acquisition and four-channel acquisition capabilities.

The extra time is then used for higher value tasks such as data analysis, root cause analysis and maintenance planning.

Use a wireless hotspot in the device to send data directly from ffeld back to the maintenance shop.

When you start another route, analysts in the maintenance shop can start analysing the data, so you can collect and analyse data at the same time.

Or send data back to a central database from a remote plant location so that it can be viewed by key stakeholders within your organisation.

Designed for you

Four-channel data collection makes bearing analysis easier and faster

Better understanding of shaft motion and machine transients with four-channel diagnostics

Longer battery life for a full shift (or more) without recharging

Full-colour touchscreen for easy navigation and detailed fault analysis, even when wearing gloves

Large screen automatically adjusts to ambient light so you can see what you need to see, wherever you are

Slim housing for comfortable one-handed operation

Fastest data acquisition speed on the market, so you spend less time in harsh environments

Advanced analysis tools, including cross-channel and transient analysis, www.honeywell-diver.com help identify root causes

Comfortable shoulder strap and built-in stand make the analyser easy to use

Bluetooth wireless communication with headset for ease of use

Predictive diagnostics help you determine the root cause of equipment problems

Versatile advanced diagnostics improve machine health

The AMS 2140 offers the industry’s most complete set of features to quickly and accurately assess the health of rotating machinery.

Even the most complex machinery in your facility. With the AMS 2140

You can perform single-, dual-, or quad-channel vibration analysis, cross-channel analysis, transient analysis, structural analysis, balancing, and motor monitoring.

The analyser’s embedded intelligence guides you through advanced diagnostic tools, providing pre-configured menus and preset technology settings.

Troubleshooting documentation in the AMS 2140 helps with initial analysis, and AMS Suite integrates with the analyser for more in-depth analysis of data.

Take only one tool to the field

When you head out to the field on a collection mission, you don’t want to have to carry multiple tools.

The AMS 2140 provides you with a single platform that enables you to perform a wide range of machine health tests.

Balancing, temperature trending, and motor diagnostic functions coexist with vibration analysis tools.

Data from all of these tests is loaded into a database that allows you to trend the data from the various tests.

This gives you a more complete picture of the machine’s condition and predicts when corrective maintenance is required.

The AMS 2140 is suitable for a wide range of rotating equipment, including variable speed machines, complex gearboxes, low speed equipment, turbomachinery, sleeve bearings, gearboxes, and more.

equipment, turbomachinery, sleeve bearing machinery and reciprocating compressors.
2024-12-17 BY
IN Emerson

Emerson AMS 6500 Protection Monitor Configuration

Pre-configured user-selectable measurement types simplify software configuration

Password protection with 4 user login levels and customisable access rights

Context-sensitive help information to quickly resolve set-up issues

Includes trending, time functions, order analyses and start/stop data for comprehensive setup.

Configuration includes setup of basic predictive functions, including troubleshooting and diagnostics

Applications

The AMS 6500 Configuration Software for Machinery Protection allows you to configure protection modules, view real-time vibration monitoring systems and sensor health.

The intuitive configuration process begins with the selection of the card type. Next, the configuration software displays a simple table view.

All configuration settings are clearly visible. Tabs help you categorise www.honeywell-diver.com information between inputs, outputs, advanced machine diagnostics and management tasks.

diagnostic and management tasks. The allowable range for each required entry is clearly visible to help you understand the range of the parameter.

Preset parameters are automatically loaded when using Emerson sensors and transducers.

Real-time data can be displayed during system configuration to verify that wiring, card settings, and instrumentation are healthy and properly connected.

Real-time information such as gap voltage, waveform data, and overall vibration data can be viewed.

Ongoing maintenance functions such as resetting latching relays or loading saved configurations can be easily performed via software.

The software can be run on a PC or laptop.

The System Configuration Software allows you to configure the following monitors of the A6000 series

The following monitors of the A6000 series can be configured:

a6110. a6120. a6125. a6140. a6150. a6151. a6210. a6220. a6310. a6312. a6312-8.

a6410. a6620. a6630. a6740.a6740-10. a6824. a6824r

Basic Predictive Features

The AMS 6500 Configuration Software has a number of built-in trending functions that allow basic troubleshooting and prediction of the machine.

Master value trends are graphically represented, showing both card health and alarm values. The software can display vibration signals as a function of time,

The software displays the vibration signal as a function of time, the date of the FFT analysis with a resolution of up to 400 lines, and the FFT phase data. The software also displays the last time the machine was started or stopped.

The configuration software visualises the data and displays velocity over time and vibration over velocity for each channel.

Configuration Software

The configuration suite contains the following sections:

CD-ROM containing the configuration of the AMS 6500 protection module

Installation instructions

2 metre configuration cable with 9-pole SUB D plug and 6-pole miniature DIN diode plug for connection to AMS 6500 Protection Monitor

9-pole SUB D DV adapter on 25-pole SUB D, type AB914F

Two adapter cables with SMB coaxial plugs on both sides for connection of oscilloscopes to the AMS 6500 Protection Monitor.

Length 3 metres, supplied by Radiall, type 296-201-794

Two adapters BNC/SMB R191 209. supplied by Radiall

USB to RS232 adapter

Configuration programme

The configuration software package contains the following programmes:

A6910 Configuration Software for AMS 6500 Protection Monitor

System requirements

To load the programme, the PC or laptop must fulfil the following minimum prerequisites:

Standard PC/laptop, Pentium II or higher, minimum clock frequency 500 MHz, CD-ROM.

RS232 interface port (or USB (when used with an external USB to RS232 converter)).

Operating System Windows 2000. Windows XP, Windows Vista or Windows 7
2024-12-17 BY
IN ABB

ABB REF 542plus Multifunctional Protection and Switching Controls

Functions

The REF542plus multifunctional protection and switchboard control unit integrates all auxiliary functions in one unit.

The multifunctional unit also has a self-monitoring function. All functions are designed as freely configurable software modules.

As a result, the various operational requirements of a MV station can be met without any problems.

The versatility of the software allows the REF542plus to be used on every switchboard regardless of the specific application requirements.

Configuration

Each protection and control application can be easily configured via the software function module, which allows the following functions to be arbitrarily defined as part of the secondary system:

LEDs for local indication (meaning and colour)

Single line diagrams showing the status of switching devices

Protection programme

Control programmes

Interlocking programmes

Automation sequences

All functions of the switchboard can be specified in co-operation with ABB. The configuration results are saved and delivered to the user together with the switchboard.

By using the “Function Block” programming language (FUPLA), the REF542plus multifunctional protection and switchboard control unit provides engineers, in

especially non-software specialists, the opportunity to easily update switchboard operation and handling.

With the REF542plus, users can fully integrate secondary systems into a true programmable controller.

This flexibility is very favourable for defining control functions for automation sequences.

This can include, for example, interlocking of switchgear, preventing the release of specific protective functions and initiating switching sequences.

The REF542plus multifunction unit offers a wide range of logic functions so that the various required control schemes can be configured.

The required control schemes are configured. The range of logic functions includes

AND logic gates

NAND logic gates

OR logic gates

NOR gates

XOR gates

Bistable and Monostable Flip-Flops

Bistable and Monostable Flip-Flops

Timers

Pulse Generator

Memory

Similar to the free definition of control schemes, each required protection scheme can www.honeywell-diver.com be configured by combining the available protection function modules.

For example, the following protection functions are available:

Timed overcurrent protection

Inverse time overcurrent protection

Directional overcurrent protection

Undervoltage or overvoltage protection

Distance protection

Transformer and motor differential protection

Cable, transformer and motor thermal protection

Reverse power protection

Synchronisation check

The parameters of the protection scheme can be changed via the HMI control unit without the use of a personal computer.

Additional functions can be performed using a personal computer running configuration software and connected to the optical interface on the front of the HMI unit.

These additional functions include

Parameter setting for the protection programme,

reading out of current measured values

Reading out the status of binary inputs and outputs,

reading out the fault recorder

Viewing the status of FUPLA logic inputs/outputs

The REF542plus allows convenient local operation and is fully interlocked to prevent switching errors.

The switching positions of the various switching devices in the switch box can be displayed on the LCD display of the HMI control unit.

If the local control mode is selected, switching operations can be entered locally via the control buttons on the HMI control unit.

Switching to other control modes is only possible using the correct electronic pushbuttons.

In remote control mode, switching operations can only be performed via a remote control unit (e.g. station automation system).

For users who wish to switch locally and remotely at the same time, a special control mode, the local and remote mode, is also available.

Interlocking is also possible between switchgear connected to the same busbar system. This requires the provision of status information between switchgear and other switchgear.

The status information must be provided by a conventional hard-wired ring bus system or by the more sophisticated ABB station automation system.

Related Product Recommendations:

IC660TBD024K Genius I/O Terminal Assembly Module

IC687BEM713B Fanuc 90-70 Series Bus Transmitter Unit

DS200KLDBG1ABC DS215KLDBG1AZZ03A Automation Module

DeltaVrm VerticalPlus Input/Output Subsystem carrier

FBM203 P0914SV Channel Isolated 8-Input RTD

FBM204 P0914SYI/O Module 4 Channel

369-HI-R-M-F-E-H-E Motor Management Relay

369-C101 Motor Management Relay

369-LO-0-M-F-E-0-0 Motor Management Relay

IC698PSA100 Fanuc RX7i Series Central Processor

IC698PSA350D Fanuc RX7i Series Central Processor

44A751101-G01 Processor Module

8115-DO-DC 8-Channel Digital Output Module
2024-12-17 BY
IN Foxboro

FOXBORO IDP10 I/A Series® Electronic Differential Pressure Transmitter

The Foxboro® brand Model IDP10 is an analogue output, two-wire d/p Cell® transmitter.

It provides accurate, reliable differential pressure measurement and transmits a 4 to 20 mA analogue output signal.

High Reliability and Value

 is available in conventional or low-profile construction.

 Excellent performance and long-term stability based on microprocessor technology.

 Industry-standard 316L ss, Co-Ni-Cr, nickel alloy(1), monel alloy, www.honeywell-diver.com or tantalum sensor materials, depending on transmitter construction.

 Available in durable aluminium or 316 SS housings; both meet NEMA 4X and IP66 ratings.

 Optional mounting bracket kits are available for duct, surface, or manifold mounting of the transmitter.

 Dual seal certified to ANSI/ISA 12.27.01-2003.

 CE marked; complies with applicable EMC, ATEX, and PED European directives.

 Designed for hazardous area installations. Versions are available to meet organisational explosion-proofing and zoning requirements.

 Standard 5-year warranty.

Affordable Smart Transmitter Features

When you need the flexibility and performance of a configurable smart transmitter, but don’t need a digital output signal, these transmitters offer excellent benefits at a very affordable price:

 Liquid crystal display (LCD) digital indicator with on-board pushbuttons

 Pushbutton configuration and calibration

– Linear or square root output

– Adjustable damping

– Forward or reverse output

– Fail-safe outputs; scale up or scale down

– Rearrange without applying pressure

 can be easily upgraded to a fully intelligent version (FoxCom™, HART® or FOUNDATION™ fieldbus)

I/A SERIES PRESSURE TRANSMITTERS The I/A Series pressure transmitter family includes d/p Cell, Gauge, Absolute, Multi-Range, Multi-Variable, and High Performance transmitters, as well as pressure seals with remote or direct connection.

and transmitters with remote or directly connected pressure seals, all featuring field-proven silicon strain gauge sensors and universal topside construction.

Modular electronics

Choose the electronics modules you need to provide just the right level of intelligence for your application and budget.

If your needs change, the modular design allows easy migration to other protocols including FoxCom, HART, FOUNDATION fieldbus and 1 to 5 V dc versions.

Electronic -A Transmitter

This transmitter uses the -A electronics module. It is a very economical analogue output transmitter with comprehensive configuration features.

The transmitter offers the most powerful features for the most applications at the lowest cost.

cost. It can even be readjusted to a new calibration range using the standard LCD indicator without applying calibration pressure.

Sensor corrosion protection

For conventional construction, 316L ss, Co-Ni-Cr, nickel alloys (2), monel alloys, gold-plated 316L ss, and tantalum materials are available.

The high corrosion resistance of CoNi-Cr (TI 037-078) means a long service life in many difficult applications

The high corrosion resistance of CoNi-Cr (TI 037-078) means a long service life in many difficult applications without the extra cost of special materials.

For flat structures LP1 and LP2. 316L stainless steel and nickel alloys (2) are used as sensor materials.

High Performance

These transmitters utilise microprocessor-based calibration for excellent accuracy and ambient temperature compensation.

Related Product Recommendations:

IC660TBD024K Genius I/O Terminal Assembly Module

IC687BEM713B Fanuc 90-70 Series Bus Transmitter Unit

369-C101 Motor Management Relay

369-LO-0-M-F-E-0-0 Motor Management Relay

IC698PSA100 Fanuc RX7i Series Central Processor

DeltaVrm VerticalPlus Input/Output Subsystem carrier

FBM203 P0914SV Channel Isolated 8-Input RTD

FBM204 P0914SYI/O Module 4 Channel

369-HI-R-M-F-E-H-E Motor Management Relay

44A751101-G01 Processor Module

8115-DO-DC 8-Channel Digital Output Module
2024-12-17 BY
IN Emerson

Emerson DeltaV™ VerticalPlus Input/Output Subsystem Carrier

Functional features:

Designed for SIS

Modular design for flexible installation

Allows for online expansion

Increased I/O density

I/O density for cabinet-mounted systems

Introduction to the DeltaV™ VerticalPlus I/O Rack

Keep your I/O subsystems running efficiently with DeltaV™ VerticalPlus I/O Racks.

The VerticalPlus platform allows you to integrate DeltaV www.honeywell-diver.com SIS logic solvers vertically, giving you the flexibility you need for cabinet design.

Power supplies/controllers and I/O carriers are modular.

You buy only what you need, but rest assured that as your system grows, you can add plug-and-play carriers-it’s easy!

The Advantage

Designed specifically for SIS. The redesigned carrier supports simplex and redundant SLS modules.

These modules communicate via a redundant safety bus, which is separate from the BPCS communications.

The VerticalPlus carrier also communicates with other SIS nodes on the vertical and horizontal carriers via redundant SISNet repeaters.

The modular design allows for flexible installation. A single T-shaped DIN rail is all that is needed to mount the power/controller carrier in place.

Fieldbus power is now independent for each individual card.

The modular design approach of the DeltaV system allows you to add I/O carriers as needed.

Allows you to expand online. Additional carriers can be added online as needed.

Increases the density of the cabinet-mounted system. Six I/O carriers can be mounted on one side of a standard 1200mm x 600mm x 2200mm cabinet.

Product Description

The VerticalPlus I/O Interface Carrier plugs into the 4-Wide Power/Controller Carrier, which provides power to the system and communication between the I/O interface and the controller.

The controller processes I/O interface information through the control module.

The VerticalPlus I/O Interface Carrier provides a separate bus field power connection for each I/O card.

The carrier is designed to support the same terminals as the horizontal carrier.

The carriers are mounted on T-shaped DIN rails. Each I/O interface carrier is supplied with connectors for direct mating together.

A single I/O subsystem supports a total of eight 8-width I/O interface carriers for a maximum of 64 local I/O interface cards.

Cable extenders are used to connect carriers that cannot be installed next to each other, allowing the carriers to be arranged in standard equipment cabinets.

The extender has two 22-pin D-type connectors and supports a dual cable fault-tolerant configuration.

Ports A and B are connected in parallel so that either port can be used.

The new Dual Carrier Extender also supports the redundant secure bus coaxial connectors used by DeltaV SIS.

The total length of the I/O bus is 6.5 metres (21.3 feet).

The VerticalPlus carrier can also be used for Zone 2 remote I/O devices to provide installation flexibility.

Related Product Recommendations:

IC660TBD024K Genius I/O Terminal Assembly Module

IC687BEM713B Fanuc 90-70 Series Bus Transmitter Unit

369-C101 Motor Management Relay

369-LO-0-M-F-E-0-0 Motor Management Relay

IC698PSA100 Fanuc RX7i Series Central Processor

DeltaVrm VerticalPlus Input/Output Subsystem carrier

FBM203 P0914SV Channel Isolated 8-Input RTD

FBM204 P0914SYI/O Module 4 Channel

369-HI-R-M-F-E-H-E Motor Management Relay

44A751101-G01 Processor Module

8115-DO-DC 8-Channel Digital Output Module

Menu
Call us 24/7+86 15396212224

Search for products

Back to Top
Product has been added to your cart